DOCUMENTATION 》 TOFFEE (and TOFFEE-DataCenter) optimized Mobile Wireless Backhaul Networks

Today I refined the first page consolidated report graphs. TOFFEE-Mocha (unlike TOFFEE) is a WAN Emulator, so the graphs are supposed to highlight this purpose and should display the overall network activity. Unlike TOFFEE, the TOFFEE-Mocha report should contain in general what is received versus what is sent across the wire. In case if the packet drop feature is enabled, you should see few missing bytes and packets. Similarly in future I may support packet duplication feature, in that case you may see more packets/bytes sent versus the packets/bytes actually received.

TrueBench is an unique open-source benchmarking system in which the core system performance and efficiency parameters are measured at extreme high resolution in the order of several million/billion µ-seconds for a given specific task. TrueBench is a part of The TOFFEE Project research.

TOFFEE-Butterscotch is an open-source software which can be used to save and optimize your Internet/WAN bandwidth. Unlike TOFFEE (and TOFFEE-DataCenter) TOFFEE-Butterscotch is a non peer-to-peer (and asymmetric) network optimization solution. This makes TOFFEE-Butterscotch an ideal tool for all Home and SOHO users.

Network MTU research and optimization of WAN Links

TOFFEE is an open-source WAN Optimization (Network Performance Optimization) software which can be used to optimize your critical networks.

PiPG is a powerful and yet simple Raspberry Pi Network Packet Generator. With PiPG you can now fabricate custom network packets and send via any Network Interface. Supports all kinds of standard Network Ports (Linux Kernel driver generated) such as Physical Network Interface ports, and an array of virtual ports such as loopback, tun/tap, bridge, etc. indispensable tool for: Network Debugging, Testing and Performance analysis Network Administrators Students Network R&D Protocol Analysis and Study Network Software Development Compliance Testing Ethical Hackers you can generate the following test traffic: L2-Bridging/Slow protocols: STP, LACP, OAM, LLDP, EAP, etc Routing protocols: RIPv1, RIPv2, IGMPv1, IGMPv2, OSPF, IS-IS, EIGRP, HSRP, VRRP, etc Proprietary protocols: CISCO, etc Generic: IPv4 TCP/UDP, etc Malformed random packets

In case if you need to deploy TOFFEE along with your existing VPN devices you can deploy the same as shown below. This will allow your VPN devices to encrypt your TOFFEE WAN Optimized network data. NOTE: Make sure about the VPN deployment topology done in the right order. Else TOFFEE (LAN side) may get VPN encrypted packets which may not be possible (and or difficult) to further optimize. Hence always make sure to deploy them in a topology suggested below so that TOFFEE devices are out of VPN tunnel.

Today I finally completed building my own private CDN. As I discussed so far in my earlier topics (Building my own CDN), I want to custom build the same step-by-step from scratch. And I don't want to for now use/buy third-party CDN subscriptions from Akamai, CloudFlare, Limelight, etc as I discussed earlier.

In the previous update (17-Jun-2016) I discussed about the upcoming new Random Packet drop feature along with other completed features. Now I completed the entire TOFFEE-Mocha Random packet drop feature. I completed all the kernel components and the UI support of the same. And to make GUI settings more organized I split the earlier Basic-Settings page into two separate pages namely: Packet Drop and Packet Delay. So this way it is simple to understand settings according to their functionality.

Today I completed doing all the changes which are meant for the new upcoming TOFFEE-Mocha release. I have increased the resolution and the range of all factor variables. Instead 1 to 10 range now they have a range of 1 to 30. Unlike before the value 1 means it is lot more intense (or in some cases less intense) and the uppermost value 30 means lot less intense (or in some cases lot intense).