VIDEOS 》 Bulk Ping Tests - WAN Acceleration

TrueBench is an unique open-source benchmarking system in which the core system performance and efficiency parameters are measured at extreme high resolution in the order of several million/billion µ-seconds for a given specific task. TrueBench is a part of The TOFFEE Project research. With TrueBench Raspberry Pi 3, Raspberry Pi 2B, Raspberry Pi 2 and other embedded SoC devices are benchmarked and you can do a comparative analysis with standard mainstream x86 devices.

PiPG is a powerful and yet simple Raspberry Pi Network Packet Generator. With PiPG you can now fabricate custom network packets and send via any Network Interface. Supports all kinds of standard Network Ports (Linux Kernel driver generated) such as Physical Network Interface ports, and an array of virtual ports such as loopback, tun/tap, bridge, etc. indispensable tool for: Network Debugging, Testing and Performance analysis Network Administrators Students Network R&D Protocol Analysis and Study Network Software Development Compliance Testing Ethical Hackers you can generate the following test traffic: L2-Bridging/Slow protocols: STP, LACP, OAM, LLDP, EAP, etc Routing protocols: RIPv1, RIPv2, IGMPv1, IGMPv2, OSPF, IS-IS, EIGRP, HSRP, VRRP, etc Proprietary protocols: CISCO, etc Generic: IPv4 TCP/UDP, etc Malformed random packets

Here is my second software development update of TOFFEE-Butterscotch. In the previous update (28-Oct-2016) I discussed about the Alerts, etc. Whereas in my first TOFFEE-Butterscotch news update I have introduced about TOFFEE-Butterscotch research, project specifications, use-cases, etc.

Here is my video article on Network Latency in WAN Networks (such as long distance Satellite links, etc) and how you can optimize the same to achieve better network performance.

Today I refined the first page consolidated report graphs. TOFFEE-Mocha (unlike TOFFEE) is a WAN Emulator, so the graphs are supposed to highlight this purpose and should display the overall network activity. Unlike TOFFEE, the TOFFEE-Mocha report should contain in general what is received versus what is sent across the wire. In case if the packet drop feature is enabled, you should see few missing bytes and packets. Similarly in future I may support packet duplication feature, in that case you may see more packets/bytes sent versus the packets/bytes actually received.

Today I have done a test setup so that I can able to connect my Android Samsung Tab via TOFFEE DataCenter. Below is my complete test topology of my setup. For demo (and research/development) context I configured TOFFEE DataCenter in engineering debug mode. So I do not need two devices for this purpose.

Timelapse Screen Capture of TOFFEE-DataCenter Network Acceleration - with new RRDtool graph support

Download TOFFEE-DATACENTER-1.3.25-1-portable.tar.xz via Google Drive share: platform independent (portable) source: TOFFEE-DATACENTER-1.2.2-1-portable.tar.xz * Alternatively download from SOURCEFORGE project site. * Here are the TOFFEE-DataCenter supported features. * To know more about the project kindly refer TOFFEE-Datacenter Documentation, News and Updates

You can build a basic TOFFEE WAN Optimization hardware completely in software layer (i.e its networking data-plane and control-plane). And if you are a product manufacturer you can make commercial WAN Optimization products with TOFFEE with software layer alone. And if you choose to improve its performance, you can use any third-party PCIe Compression Accelerator cards.

Assume you have two sites (such as Site-A and Site-B) connected via slow/critical WAN link as shown below. You can optimize this link by saving the bandwidth as well possibly improve the speed. However, the WAN speed can be optimized only if the WAN link speeds are below that of the processing latency of your TOFFEE installed hardware. Assume your WAN link is 12Mbps, and assume the maximum WAN optimization speed/capacity of Raspberry Pi is 20Mbps, then your link will get speed optimization too. And in another case, assume your WAN link is 50Mbps, then using the Raspberry Pi as WAN Optimization device will actually increase the latency (i.e slows the WAN link). But in all the cases the bandwidth savings should be the same irrespective of the WAN link speed. In other words, if you want to cut down the WAN link costs via this WAN Optimization set up, you can always get it since it reduces the overall bandwidth in almost all the cases (including encrypted and pre-compressed data).