EDUCATION :: Page Not Found

Here is a list of TOFFEE-DataCenter features supported. TOFFEE-DataCenter currently supports some of the important features such as loss-less network data compression, Packet Deduplication (protocols/applications supported), Application Acceleration, TCP Acceleration, dynamic MTU optimization, data packaging, hardware offload support, etc.

Here is a complete chart comprising popular communication data network standards and their respective transfer rates. I hope this reference chart will help network engineers and network software developers while performing networking tests and experiments, building WAN/network products, building WAN simulated networks of a specific standard and so on. This may also helps us to track technological advancements of communication data networks.

WAN Network data can be optimized at various levels depending upon the network applications, protocols, topology and use-cases. So the amount of data you can optimize will depend on the strategy you choose to optimize. Such as: Network Packet level optimization, Session level optimization, File level optimization, etc.

TOFFEE/TOFFEE-DataCenter can be used to optimize Ad-Hoc Mobile Wireless Mesh-Networks. To learn more about the same here are some references: B.A.T.M.A.N. - https://en.wikipedia.org/wiki/B.A.T.M.A.N. Mobile ad hoc network (MANET) - https://en.wikipedia.org/wiki/Mobile_ad_hoc_network Wireless ad hoc network (WANET) - https://en.wikipedia.org/wiki/Wireless_ad_hoc_network open-mesh.org (Open Mesh) Wiki - https://www.open-mesh.org/projects/open-mesh/wiki

Here is my second software development update of TOFFEE-Butterscotch. In the previous update (28-Oct-2016) I discussed about the Alerts, etc. Whereas in my first TOFFEE-Butterscotch news update I have introduced about TOFFEE-Butterscotch research, project specifications, use-cases, etc.

Here is a complete log of my lab battery purchase, service record which I maintain in Google drive. These I use for my home (or my family generic use) as well as a part of my home lab. I maintain a detailed log this way to monitor the failure rate of these batteries. This will allow me to select a specific brand/model which has higher success rate and to monitor any premature failure/expiry. The service log helps me to monitor and schedule the next service routine so that I can maintain these batteries in tip-top condition.

I started TOFFEE-Mocha WAN Emulation software development on 1-June-2016. I took the existing TOFFEE components as a base. Although the TOFFEE-Mocha is entirely an independent fresh Open-Source WAN Emulation solution. Ever since I am in the process of defining and inventing features. So far I come up with the most important feature which is expected to be present in any WAN Emulation software is the packet delay option.

Assume you have two sites (such as Site-A and Site-B) connected via slow/critical WAN link as shown below. You can optimize this link by saving the bandwidth as well possibly improve the speed. However, the WAN speed can be optimized only if the WAN link speeds are below that of the processing latency of your TOFFEE installed hardware. Assume your WAN link is 12Mbps, and assume the maximum WAN optimization speed/capacity of Raspberry Pi is 20Mbps, then your link will get speed optimization too. And in another case, assume your WAN link is 50Mbps, then using the Raspberry Pi as WAN Optimization device will actually increase the latency (i.e slows the WAN link). But in all the cases the bandwidth savings should be the same irrespective of the WAN link speed. In other words, if you want to cut down the WAN link costs via this WAN Optimization set up, you can always get it since it reduces the overall bandwidth in almost all the cases (including encrypted and pre-compressed data).

Today I have done a test setup so that I can able to connect my Android Samsung Tab via TOFFEE DataCenter. Below is my complete test topology of my setup. For demo (and research/development) context I configured TOFFEE DataCenter in engineering debug mode. So that I do not need two devices for this purpose.